so here is the new board I am working from:
<\/p>\n\n\n\n
![\"\"](\"https:\/\/wordpress.hertell.nu\/wp-content\/uploads\/2022\/08\/IMG_20220814_103009-scaled.jpg\")
<\/a><\/figure>\n\n\n\n<\/a><\/figure>\n\n\n\nAs you can see. pretty much same state except that I skipped sockets for the chipset here. (sockets are a reason for issues)<\/p>\n\n\n\n
Anyway time to go to the next part of this and that is simply to add the 2 9Pin DSub and the keyboard connector. A hint is to make sure you have no shorts on the resistor\/capacitornets now. as it is WAY more easy to fix that with connectors off. \ud83d\ude42 Now with that done. time to get the Flickerfixer to work.<\/p>\n\n\n\n Program the 2 22V10 GALs and solder them on U460 and U461. It is a part of the built in VGA Switch. with this it works. it will be up to you to find documentation about this. (I MIGHT update this build at a later stage about this) I put the GND on the leftover pin at the jumper and probe pin 9.<\/p>\n\n\n\n for me it started with:<\/p>\n\n\n\n Picture doesn’t show that good. but wave is not even.. so turn the VC470 with a isolated screwdriver until the signal gets to a nice even signal:<\/p>\n\n\n\n And you should also get something on the screen. you do not need an oscilloscope but it is more easy when you have it.<\/p>\n\n\n\n Now it is time for the RTC.<\/p>\n\n\n\n Solder in oscillator at Y490, Batteryholder (this was kinda tricky as the holes did not fit for me. some bending of pins and I managed it. NiCad: Install R192 (bottom side), don’t install D192 Now just solder in the FAN Connector and the Zorro Connectors:<\/p>\n\n\n\n on some parts the zorroconnector pins are quite long so you MIGHT need to trim them on the other side (cutting off extra long pins)<\/p>\n\n\n\n IF you do not want to use the DSP. you are actually done now. just put on the electrolytes and the machine is done.<\/p>\n\n\n\n However .. time for the DSP: <\/p>\n\n\n\n You MIGHT want to wait with the connector until you tested the DSP.<\/p>\n\n\n\n Test the DSP with software in the archive:<\/p>\n\n\n\n And you are DONE.<\/p>\n\n\n\n
status with connectors on:<\/p>\n\n\n\n<\/a><\/figure>\n\n\n\n
TS5V330 at U490, U491
STG719STR at U492, U493, U494 and U495
74FCT16374 at U478, Y479
D42102 at U472, U473, U474, U475, U476 and U477.
MSM514221 at U466, U467, U468, U469, U470 and U471
NE564 at U482
VC470 (2-10pF)
74HC04 at U480
74F163 at U462, U463, U464 and U483
74F175 at U465
74F02 at U481
74F74 at U454
VGA Connector at CN480
1K Trim at VR470
Switch at SW481
Connectors at CN490 and CN491.
NOTE on CN490 you will need to put some jumpers like this:
<\/p>\n\n\n\n<\/a><\/figure>\n\n\n\n
now you will need to trim the VC470 to get a picture.. you can use a oscilloscope to help.
<\/p>\n\n\n\n<\/a><\/figure>\n\n\n\n<\/a><\/figure>\n\n\n\n<\/a><\/figure>\n\n\n\n
Put in VC190, and the RTC Chip.
NOTE Depending of battery you want to use:
<\/p>\n\n\n\n
Lithium: Install D192, don’t install R192
as I will use CR2032 coincell battery, I installed D192 and made sure R192 was not there.<\/p>\n\n\n\n<\/a><\/figure>\n\n\n\n<\/a><\/figure>\n\n\n\n<\/a><\/figure>\n\n\n\n
This is not a 100% done project. I woud recoment looking at:
https:\/\/github.com\/realA10001986\/AmigaDSP3210
<\/a>and:
https:\/\/www.a1k.org\/forum\/index.php?threads\/76673\/<\/a>
as this is just the TL;DR version of it \ud83d\ude42
Add Delayline at U702 or U703 depending on your Chip.
You need to change the GAL Codes and on the link above there are new JED files so program U122, U124 and U701 from that archive and U123 from the original AA3000+ archive.
I used 5ns GALs for all.
Solder in the DSP.<\/p>\n\n\n\n<\/a><\/figure>\n\n\n\n<\/a><\/figure>\n\n\n\n<\/a><\/figure>\n\n\n\n